Skip to content

DexcomG6.md

Latest commit

 

History

History
75 lines (47 loc) · 4.89 KB

DexcomG6.md

File metadata and controls

75 lines (47 loc) · 4.89 KB

Dexcom G6 et ONE

Les bases en premier

  • Follow general CGM hygiene and setting sensor recommendation here.

General hints for looping with G6 and ONE

  • Recent transmitters are called Firefly. Sensors cannot be restarted without removing the transmitter, which itself cannot be reset, they also do not generate raw data.

  • If you are restarting sensors, ensure you are ready to calibrate and keep an eye on variation.

  • Pre-soaking of the G6/ONE with factory calibration is likely to give variation in results. Si vous faites une pré-installation, alors pour obtenir les meilleurs résultats, vous devrez probablement calibrer le capteur.

Read more in the article published by Tim Street at www.diabettech.com.

If using G6 or ONE with xDrip+

  • If you are using a recent (Firefly) transmitter, preemptive restarts are ignored.

  • If you are using a modded transmitter you do not need to use preemptive restarts.

  • If you are using an old rebatteried transmitter, the safest thing to do is disable preemptive restarts. Though, in this case you will have to use the G6 in non-native mode (which is unadvisable as it disables factory calibration and doesn't filter noisy readings), or else the sensor will stop after 10 days.

  • The Dexcom G6 and ONE transmitters can simultaneously be connected to the Dexcom receiver (or alternatively the t:slim pump) and one app on your phone.

  • When using xDrip+ as receiver uninstall the Dexcom app first. You cannot connect xDrip+ and Dexcom app with the transmitter at the same time!

  • If you need Clarity and want to profit from xDrip+ alarms use the BYODA (only G6) with local broadcast to xDrip+.

  • You can also use xDrip+ as a companion app of the official Dexcom app, but you might experience delays in BG readings.

  • If not already set up, download xDrip+ and follow the instructions on xDrip+ settings page.

  • Select xDrip+ in in ConfigBuilder, BG Source.

  • Adjust settings in xDrip+ according to xDrip+ settings page

(DexcomG6-if-using-g6-with-build-your-own-dexcom-app)=

Si vous utilisez G6 avec votre propre application Dexcom

:class: warning
Dexcom G6 BYODA is now a very old version of the app and cannot be updated.

BYODA broadcast options

  • Cette application vous permet d'utiliser votre Dexcom G6 avec n'importe quel smartphone Android.
  • Uninstall the original Dexcom app or patched Dexcom app if you used one of those previously (do not stop the currently running sensor)
  • Install the downloaded apk
  • Entrez le code du capteur et le numéro de série du transmetteur dans l'application patchée.
  • In phone settings go to apps > Dexcom G6 > permissions > additional permissions and press 'Access Dexcom app'.
  • Après une courte période BYODA devrait recevoir le signal du transmetteur.

Settings for AAPS

  • Select 'Dexcom App (patched)' in in ConfigBuilder, BG Source.

  • If you don't receive any values select any other data source, then re-select 'Dexcom App (patched)' to trigger the demand for permissions to establish the connection between AAPS and BYODA-broadcast.

Paramètres pour xDrip+

  • Sélectionnez '640G / Eversense' comme source de données.
  • Command 'start sensor' must be performed in xDrip+ in order to receive values. This will not affect your current sensor controlled by Build Your Own Dexcom App.

(DexcomG6-troubleshooting-g6)=

Troubleshooting G6 and ONE

Dexcom G6/ONE specific troubleshooting

  • Scroll down to Troubleshooting here.

Dépannage général

General Troubleshooting for CGMs can be found here.

Nouvel émetteur avec capteur en cours

If you happen to change transmitter during a running sensor session you might try to remove the transmitter without damaging the sensor mount. A video can be found here. If you opt for this solution instead, you must be careful to avoid damaging sensor contacts with the strip.