Merge pull request #3595 from plbossart/merge/sound-upstream-20220418

Merge/sound upstream 20220418

Author: plbossart

.mailmap

@@ -391,6 +391,10 @@ Uwe Kleine-König <ukleinek@strlen.de>
 Uwe Kleine-König <ukl@pengutronix.de>
 Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
 Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
+Vasily Averin <vasily.averin@linux.dev> <vvs@virtuozzo.com>
+Vasily Averin <vasily.averin@linux.dev> <vvs@openvz.org>
+Vasily Averin <vasily.averin@linux.dev> <vvs@parallels.com>
+Vasily Averin <vasily.averin@linux.dev> <vvs@sw.ru>
 Vinod Koul <vkoul@kernel.org> <vinod.koul@intel.com>
 Vinod Koul <vkoul@kernel.org> <vinod.koul@linux.intel.com>
 Vinod Koul <vkoul@kernel.org> <vkoul@infradead.org>

Documentation/dev-tools/kunit/start.rst

@@ -41,13 +41,18 @@ or ``VFAT_FS``. To run ``FAT_KUNIT_TEST``, the ``.kunitconfig`` has:
 	CONFIG_MSDOS_FS=y
 	CONFIG_FAT_KUNIT_TEST=y
 
-1. A good starting point for the ``.kunitconfig``, is the KUnit default
-   config. Run the command:
+1. A good starting point for the ``.kunitconfig`` is the KUnit default config.
+   You can generate it by running:
 
 .. code-block:: bash
 
 	cd $PATH_TO_LINUX_REPO
-	cp tools/testing/kunit/configs/default.config .kunitconfig
+	tools/testing/kunit/kunit.py config
+	cat .kunit/.kunitconfig
+
+.. note ::
+   ``.kunitconfig`` lives in the ``--build_dir`` used by kunit.py, which is
+   ``.kunit`` by default.
 
 .. note ::
    You may want to remove CONFIG_KUNIT_ALL_TESTS from the ``.kunitconfig`` as

Documentation/devicetree/bindings/display/bridge/chipone,icn6211.yaml

@@ -51,7 +51,6 @@ properties:
           Video port for MIPI DPI output (panel or connector).
 
     required:
-      - port@0
       - port@1
 
 required:

Documentation/devicetree/bindings/display/bridge/toshiba,tc358762.yaml

@@ -39,7 +39,6 @@ properties:
           Video port for MIPI DPI output (panel or connector).
 
     required:
-      - port@0
       - port@1
 
 required:

Documentation/devicetree/bindings/display/panel/panel-mipi-dbi-spi.yaml

@@ -83,6 +83,8 @@ properties:
 required:
   - compatible
   - reg
+  - width-mm
+  - height-mm
   - panel-timing
 
 unevaluatedProperties: false

Documentation/devicetree/bindings/net/ethernet-controller.yaml

@@ -106,6 +106,12 @@ properties:
   phy-mode:
     $ref: "#/properties/phy-connection-type"
 
+  pcs-handle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Specifies a reference to a node representing a PCS PHY device on a MDIO
+      bus to link with an external PHY (phy-handle) if exists.
+
   phy-handle:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:

Documentation/devicetree/bindings/net/micrel.txt

@@ -45,20 +45,3 @@ Optional properties:
 
 	In fiber mode, auto-negotiation is disabled and the PHY can only work in
 	100base-fx (full and half duplex) modes.
-
- - lan8814,ignore-ts: If present the PHY will not support timestamping.
-
-	This option acts as check whether Timestamping is supported by
-	hardware or not. LAN8814 phy support hardware tmestamping.
-
- - lan8814,latency_rx_10: Configures Latency value of phy in ingress at 10 Mbps.
-
- - lan8814,latency_tx_10: Configures Latency value of phy in egress at 10 Mbps.
-
- - lan8814,latency_rx_100: Configures Latency value of phy in ingress at 100 Mbps.
-
- - lan8814,latency_tx_100: Configures Latency value of phy in egress at 100 Mbps.
-
- - lan8814,latency_rx_1000: Configures Latency value of phy in ingress at 1000 Mbps.
-
- - lan8814,latency_tx_1000: Configures Latency value of phy in egress at 1000 Mbps.

Documentation/devicetree/bindings/net/xilinx_axienet.txt

@@ -26,7 +26,8 @@ Required properties:
 		  specified, the TX/RX DMA interrupts should be on that node
 		  instead, and only the Ethernet core interrupt is optionally
 		  specified here.
-- phy-handle	: Should point to the external phy device.
+- phy-handle	: Should point to the external phy device if exists. Pointing
+		  this to the PCS/PMA PHY is deprecated and should be avoided.
 		  See ethernet.txt file in the same directory.
 - xlnx,rxmem	: Set to allocated memory buffer for Rx/Tx in the hardware
 
@@ -68,6 +69,11 @@ Optional properties:
 		  required through the core's MDIO interface (i.e. always,
 		  unless the PHY is accessed through a different bus).
 
+ - pcs-handle: 	  Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
+		  modes, where "pcs-handle" should be used to point
+		  to the PCS/PMA PHY, and "phy-handle" should point to an
+		  external PHY if exists.
+
 Example:
 	axi_ethernet_eth: ethernet@40c00000 {
 		compatible = "xlnx,axi-ethernet-1.00.a";

Documentation/devicetree/bindings/sound/cirrus,cs35l41.yaml

@@ -75,6 +75,19 @@ properties:
     maximum: 3
     default: 2
 
+  cirrus,boost-type:
+    description:
+      Configures the type of Boost being used.
+      Internal boost requires boost-peak-milliamp, boost-ind-nanohenry and
+      boost-cap-microfarad.
+      External Boost must have GPIO1 as GPIO output. GPIO1 will be set high to
+      enable boost voltage.
+      0 = Internal Boost
+      1 = External Boost
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 1
+
   cirrus,gpio1-polarity-invert:
     description:
       Boolean which specifies whether the GPIO1
@@ -131,9 +144,32 @@ required:
   - compatible
   - reg
   - "#sound-dai-cells"
-  - cirrus,boost-peak-milliamp
-  - cirrus,boost-ind-nanohenry
-  - cirrus,boost-cap-microfarad
+
+allOf:
+  - if:
+      properties:
+        cirrus,boost-type:
+          const: 0
+    then:
+      required:
+        - cirrus,boost-peak-milliamp
+        - cirrus,boost-ind-nanohenry
+        - cirrus,boost-cap-microfarad
+    else:
+      if:
+        properties:
+          cirrus,boost-type:
+            const: 1
+      then:
+        required:
+          - cirrus,gpio1-output-enable
+          - cirrus,gpio1-src-select
+        properties:
+          cirrus,boost-peak-milliamp: false
+          cirrus,boost-ind-nanohenry: false
+          cirrus,boost-cap-microfarad: false
+          cirrus,gpio1-src-select:
+            enum: [1]
 
 additionalProperties: false
 
@@ -150,6 +186,8 @@ examples:
           VA-supply = <&dummy_vreg>;
           VP-supply = <&dummy_vreg>;
           reset-gpios = <&gpio 110 0>;
+
+          cirrus,boost-type = <0>;
           cirrus,boost-peak-milliamp = <4500>;
           cirrus,boost-ind-nanohenry = <1000>;
           cirrus,boost-cap-microfarad = <15>;

Documentation/devicetree/bindings/sound/tas27xx.yaml

@@ -20,7 +20,6 @@ properties:
   compatible:
     enum:
       - ti,tas2764
-      or
       - ti,tas2780
 
   reg: